ESP

Select Wire Lengths In the Options Box Above Both of the motors spin clockwise when the controller is in the forward direction mode. The motors in this kit have forward brush timing so they spin at different speeds in the clockwise and counterclockwise directions. Due to this both motors should be installed so they spin clockwise when the vehicle is moving forward. The SWT-23 handlebar mount switch with red button is wired as the reverse switch, and the SWT-95 toggle switch is wired as the...

Wire Routing Chart The Controller to Power Relay wires are approximately 6 Inches long.Choose the chain and wire lengths which are needed in the 'Choose Your Options' box above. We install matching connectors on every part of this kit and label them so all you have to do is plug everything together. For optimal power and performance the motor should be installed so its shaft rotates clockwise when the vehicle is moving forward. The key switch is the on/off power switch and the red push button...

Two 12 Volt 15Ah batteries. The red button on the thumb throttle is wired as the power switch. When this kit is used with 12" (30cm) wheels the top speed is around 3 MPH, which is normal walking speed. The motor speed can be variably controlled from a full stop to top speed and everywhere in between with the included thumb throttle. The freewheel to axle adapter in this kit fits 3/4" axles and has a 3-16" keyway. Freewheel to axle adapters for different size axles are available upon request....

Wire Routing The key switch is wired as the on/off power switch and the toggle switch is wired as the forward/reverse switch. The controller is programmable so the motor rotates clockwise or counterclockwise in the forward direction.

This is a no batteries (NB) kit which does not include the batteries and battery charger. The two gear motors in this kit have clockwise shaft rotation and should be used with clockwise shaft rotation for best performance. When these gear motors are run counterclockwise their shaft speed will be slower then when run clockwise, so we recommend installing both motors so they run clockwise when the vehicle is moving forward. This kit contains 2 quantity of HNS-137, 2 quantity of MOT-36600G, 2...

Wire Routing Chart This kit was originally made for converting a gas engine powered DR Powerwagon self-propelled wheelbarrow to electric power, however, it can be used for powering beach wagons and carts or anything that needs to run at a slow speed and have a lot of power. #420 chain with a master link options are available in the Choose Your Options area. We install matching connectors on every part in this kit and label them so all you have to do is plug everything together. The throttle in...

The SWT-23 handlebar mount switch with red button is wired as the reverse switch and the red switch on the throttle is wired as the on/off main power switch. These functions of these switches could be changed upon request. The battery pack wiring harness has 6.3mm ID ring terminals for larger batteries with top post terminals.The battery charger is 24 Volts 5 Amps and is large enough to charger a battery pack made from two 12 Volt 35 Ah batteries. The motor in this kit has a 9 tooth sprocket...

Wire Routing Chart Details about this kit: We install matching connectors on every part of this kit and label them so all you have to do is plug everything together. Choose axle sprocket size, freewheel to axle adapter size, length of #420 chain with master link, and wire length options above. Specifications for the 5-hole freewheel sprockets available with this kit: 5-Hole Freewheels Sprockets for #41 and #420 Chain ...

Powered, geared, and test proven for speeds up to 26 MPH. This NB (no batteries) series kit is the exact same kit as our KIT-MX481800-1 kit only without the batteries. If you already purchased a 48 Volt battery pack to overvolt a Razor MX500, MX650 or SX500 dirt bike and now want even more power and speed then this is the right kit for you. The switch on the throttle activates the speed limiter function of the controller. When the controller's speed limiter function is switched on the motor...

Powered, geared, and test proven for speeds up to 26 MPH. This NB (no batteries) series kit is the exact same kit as our KIT-MX481800-2 kit only without the batteries or battery charger. There is the option to add a 48 Volt 1.6 Amp charger for lead-acid batteries to this kit if needed though. If you already purchased a 48 Volt battery pack to overvolt a Razor MX500, MX650 or SX500 dirt bike and now want even more power and speed then this is the right kit for you. The key switch on the...

Powered, geared, and test proven for speeds up to 26 MPH. This NB (no batteries) series kit is the exact same kit as our KIT-MX481800-3 kit only without the batteries. If you already purchased a 48 Volt battery pack to overvolt a Razor MX500, MX650 or SX500 dirt bike and now want even more power and speed then this is the right kit for you. The switch on the throttle activates the speed limiter function of the controller. When the controller's speed limiter function is switched on the motor...

Premium Rear Axle Chain Tension Adjuster Set for 10mm Axle Set of two rear axle chain or belt tension adjusters for the rear wheel of electric scooters and bikes, also popular for high end BMX bicycles. This high quality adjuster is CNC machined from 7005 aluminum with black anodized finish, hi-ten steel bolt, lock nut, and washer. Large dropout support for high stability. Axle Compatibility: For 10mm OD Axles In and Out Adjustment Range: 20mm Overall Dimensions: 2-1/4" Long x 1-1/8" High...