ESP

The motor in this kit has a native clockwise shaft rotation direction and has forward brush timing so it is best to design the dolly to have the motor running clockwise when the dolly is moving in the forward direction. The motor in this kit has a 10-tooth sprocket for #41 and #420 chain (both of these chain sizes work with this motor's sprocket). We have wheel and axle sprockets and sprocket-to-axle hubs that can be used with this kit. Need sprockets or chain for this project? Click below to...

Toggle switch to controller wire length 48" Throttle to controller wire length 48" Battery pack to controller wire length 24" Charger port wire length 24" Motor to controller wire length 24" The toggle switch has 48" of wire so it can be mounted on the front of the Dune Buggy if wanted. This wire length can be shortened on request. The chain with master link in this kit is oversized and will need to be shortened to the correct length after the motor is installed. Two pieces of 1/4” threaded...

48 Volt 1800 Watt Controller and Throttle Kit for Li-ion and LiFePO4 Battery Works with 48 Volt 1500 Watt, 48 Volt 1600 Watt, and 48 Volt 1800 Watt brushless DC (BLDC) motors.For sensored BLDC motors only, not compatible with sensorless BLDC motors. Operates motor in clockwise shaft rotation and can be rewired to run motor in counterclockwise shaft rotation.The controller has 37 Volt low Voltage protection and is for use with a 48 Volt lithium battery. The throttle will have labeled...

Variable Speed Throttle and Controller Kit Converts single-speed Razor scooters and bikes to have variable speed control. This kit is also available with a top speed adjustable limiter. Fits the following Razor models: E200 and E200S Scooter Version 13+ E225 and E225S Scooter Version 13+E250 Scooter Version 13+ E300 and E300S Scooter Version 11 and 13+ E325 Scooter Version 11 and 13+ ...

Variable Speed Throttle and Controller Kit with Top Speed Adjustable Limiter Converts single-speed Razor scooters and bikes to have variable speed control. This kit is also available without a top speed adjustable limiter. Fits the following Razor models: E200 and E200S Scooter Version 13+ E225 Scooter Version 13+ E300 and E300S Scooter Version 11 and 13+ E325 Scooter Version 11 and 13+ ...

Plug and play power upgrade kit for version 37 and up MX350 and MX400 dirt bikes and for all versions of SX350 dirt bikes. This kit has a variable-speed twist throttle and controller. Includes a large heavy-duty double-sided foam mounting tape pad for the controller. 24 Volt 450 Watt motor has the same bolt-hole pattern as the bike's original motor. Provides around the same top speed as the original motor with improved acceleration and hill climbing ability. A faster top speed could be...

Wire Routing Chart We install matching connectors on every part of this kit and label them so all you have to do is plug everything together. Choose the wire length options above.The motor in this kit has a 10-tooth sprocket for #420 chain. The switch on the throttle is the on-off power switch and the panel mount rocker switch is the reverse switch. Need sprockets or chain? Click below to view our full selection of sprockets and chains including custom-made wheel and axle sprockets. Sprockets...

Wire Routing The key switch is wired as the on/off power switch and one of the toggle switches is wired as the forward/reverse switch. The other toggle switch is the trainer switch that is wired to the Throttle Top Speed Adjustable Limiter and it turns the speed limiter on and off so the go kart can be used at either its full range of speed or at a reduced range of speed for training purposes. We have wheel and axle sprockets for T8F (8mm) and #35 chain which can be used with this kit. Click...

Wire Routing ChartThe controller to junction box wires are approximately 5 inches long. This is an NB (No Batteries) kit. It is also Available With Batteries. Select wire length options above. The controller can wired so the motor runs clockwise or counterclockwise. A reverse switch can be wired to the controller if needed. This kit has a motor with mounting base. This same kit is available with a motor without mounting base. ...

Powered, geared, and test proven for speeds up to 26 MPH. The key switch on the throttle is wired as the bike's main on-off power switch. The bike's original power switch activates the speed limiter function of the controller. When the controller's speed limiter function is switched on the motor will operate at a reduced power level for slower speeds and a longer range and ride-time. This modification kit requires custom installation (mounting) of the batteries (batteries not included) and the...

Wire Routing The key switch is wired as the on/off power switch and the toggle switch is wired as the forward/reverse switch. The controller is programmable so the motor rotates clockwise or counterclockwise in the forward direction. We have wheel and axle sprockets for 8mm and #35 chain which can be used with this kit. Click below to view our full selection of sprockets and chains. Sprockets Chains ...

Wire Routing The motor in this kit has an 11-tooth motor sprocket for #420 chain. We carry axle sprockets and axle sprocket hubs for #420 chain that are compatible with this kit.This kit does not include a battery pack, charger, or charger port. Since this kit has a forward-reverse switch it can not be used with a freewheel and it needs to be used with an axle sprocket hub.  Need a sprocket and axle sprocket hub? Click below to view our full selection of these parts. Sprockets ...