ESP

48 Volt 1800 Watt Controller and Throttle Kit for Sealed Lead-Acid Battery Pack Works with 48 Volt 1500 Watt, 48 Volt 1600 Watt, and 48 Volt 1800 Watt brushless DC (BLDC) motors.For sensored BLDC motors only, not compatible with sensorless BLDC motors. Operates motor in clockwise shaft rotation and can be rewired to run motor in counterclockwise shaft rotation.The controller has 42 Volt low Voltage protection and is for use with a 48 Volt lead-acid battery pack. The throttle will have...

Shipping weight of this kit is 75 pounds. Wire Lengths: Power switch to controller wire length 9"Throttle to controller wire length 60"Charger port to controller wire length 12"Controller to junction box wire length 6"Battery pack to junction box wire length 12"Motor to junction box wire length 24"

Wire Routing Shipping weight is 65 pounds. The key switch is wired as the on/off power switch and the toggle switch is wired as the forward/reverse switch. The controller is programmable so the motor rotates clockwise or counterclockwise in the forward direction. We have wheel and axle sprockets for 8mm and #35 chain which can be used with this kit. Click below to view our full selection of sprockets and chains. Sprockets Chains ...

Wire Routing This is a no batteries (NB) kit. The battery wiring harness fits batteries with 1/4" wide push-on spade (F2) connectors. The key switch is wired as the on/off power switch and the toggle switch is wired as the forward/reverse switch. The controller is programmable so the motor rotates clockwise or counterclockwise in the forward direction. ...

Shipping weight of this kit is 75 pounds. Wire Lengths: Power switch to controller wire length 9"Throttle to controller wire length 60"Charger port to controller wire length 12"Controller to junction box wire length 6"Battery pack to junction box wire length 12"Motor to junction box wire length 24"

Wire Routing Chart The controller to junction box wires are approximately 5 inches long. Select wire length options above. Controller can be programmed so motor runs clockwise or counterclockwise when the reverse switch is in the forward position.

Wire Routing The key switch is wired as the on/off power switch and the toggle switch is wired as the forward/reverse switch. The controller is programmable so the motor rotates clockwise or counterclockwise in the forward direction. We have wheel and axle sprockets for 8mm and #35 chain which can be used with this kit. Click below to view our full selection of sprockets and chains. Sprockets Chains ...

Wire Routing The key switch is wired as the on/off power switch and the toggle switch is wired as the forward/reverse switch. The controller is programmable so the motor rotates clockwise or counterclockwise in the forward direction. Need an axle sprocket, axle sprocket hub, or additional chain to complete your project? Click below to view our full selection of sprockets, axle sprocket hubs, and chains. Sprockets Axle Sprocket Hubs Chains ...

Wire Routing Chart Includes 10 tooth motor sprocket for #35 chain.This kit has reverse with a toggle switch that controls forward and reverse directions. The controller can be programmed to run the motor clockwise or counterclockwise when the forward-reverse switch is in the forward position so the motor can be mounted with its shaft on the left side or right side of the go-kart. This kit has a high-medium-low speed toggle switch which controls how fast the go-kart will run at. Select low...

Wire Routing Chart This kit includes batteries. We also have this kit available Without Batteries. Includes 11-tooth motor sprocket for T8F (8mm) chain.This kit has reverse with a toggle switch that controls forward and reverse directions. The motor can be wired to run the motor clockwise or counterclockwise when the forward-reverse switch is in the forward position so the motor can be mounted with its shaft on the left side or right side of the go-kart. This kit has a high-medium-low speed...

Wire Routing Chart Motor has 11-tooth sprocket for T8F chain factory installed, and kit includes a 9-tooth motor sprocket for T8F chain.This kit has reverse with a toggle switch that controls forward and reverse directions. The controller can be wired to run the motor clockwise or counterclockwise when the forward-reverse switch is in the forward position, so the motor can be mounted with its shaft on the left side or right side of the go-kart. We have wheel and axle sprockets for T8F chain,...

Wire Routing Chart This is a No Batteries (NB) kit. This kit is also available with batteries.Includes 10 tooth motor sprocket for #35 chain.This kit has reverse with a toggle switch that controls forward and reverse directions. The controller can be programmed to run the motor clockwise or counterclockwise when the forward-reverse switch is in the forward position so the motor can be mounted with its shaft on the left side or right side of the go-kart. This kit has a high-medium-low speed...