SH

36 Volt 750 Watt Electric Scooter Motor 36V 750W 2800 RPM electric scooter motor. Powerful four brush permanent magnet design with 100% ball bearing construction. Includes 11 tooth sprocket for #25 chain. 8.5mm x 10mm sprocket mounting area. Different size sprockets are available for this motor.24" long power leads. Shaft rotation reversible by reversing power leads. Motor shaft starts at 12mm OD and is stepped down to 10mm OD with two flat spots that are 8.5mm apart where the sprocket mounts,...

36 Volt 750 Watt Electric Scooter Motor 36V 750W 2800 RPM electric scooter motor. Powerful four brush permanent magnet design with 100% ball bearing construction. Includes 11 tooth sprocket for #25 chain. 8.5mm x 10mm sprocket mounting area.Different size sprockets are available for this motor. 18" long power leads. Shaft rotation reversible by reversing power leads. Motor shaft starts at 12mm OD and is stepped down to 10mm OD with two flat spots that are 8.5mm apart where the sprocket...

36 Volt 750 Watt Speed Controller with 5-Pin Throttle Connector 36V 750W Electric Scooter Speed Controller for 36 Volt eZip, IZIP, Mongoose, and Schwinn electric scooters with 5 pin throttles. Designed for 36 Volt motors up to 750 Watts. Maximum current 30 Amps. Under Voltage protection 31 Volts. Current limiting feature helps prevent controller and motor damage due to over-current conditions. Under voltage protection feature helps prevent over-discharge and extends battery life. Wiring...

36 Volt 800 Watt Electric Scooter Motor 36V 800W 2750 RPM electric scooter motor. Rated Current: 29.2APowerful four brush permanent magnet design with 100% ball bearing construction. Includes 11 tooth sprocket for #25 chain. 8.5mm x 10mm sprocket mounting area. Different size sprockets are available for this motor.24" long power leads. Shaft rotation reversible by reversing power leads.Motor shaft starts at 12mm OD and is stepped down to 10mm OD with two flat spots that are 8.5mm apart where...

36 Volt 800 Watt Electric Scooter/Pocket Bike Motor 36V 800W 3000 RPM 28.5 Amp electric scooter/pocket bike motor. Powerful four brush permanent magnet design with 100% ball bearing construction. Includes 11 tooth sprocket for 8mm chain. 12 gauge power leads. The two thick red and black wires are for motor power. The two thin red and black wires go to a temperature sensor inside of the motor and are optional to use so they do not need to be connected to anything for the motor to operate. If...

HRN-36, 36 Volt Electric Scooter Horn

36V 1000W Speed Controller for eZip, IZIP, and Schwinn 1000 Series Electric Scooter 5 wire throttle connector. 36 Volts 1000 Watts. Wiring Directions

36 Volt 1000 Watt Speed Controller for eZip®, IZIP®, and Schwinn® 1000 Series Electric Scooter (6 Wire Throttle Connector) 6 wire throttle connector. Rated 36 Volts 1000 Watts. Wiring Directions

36V 500W Electric Scooter Speed Controller Designed for 36 Volt motors up to 500 Watts. Maximum current 25 Amps. Under Voltage protection 31 Volts. Current limiting feature helps prevent controller and motor damage due to over-current conditions. Under voltage protection feature helps prevent over-discharge and extends battery life. Uses standard 3-wire variable speed hall-effect throttle. Item # SPD-36500C Wiring Directions ...

37 Tooth Rear Wheel Wheel Sprocket for #428 Chain 154mm (6.06") OD 48mm (1.89") ID 7mm thick. 8.8mm ID bolt holes. 4 bolt mounting pattern. Adjacent bolt holes are spaced 48mm (1.89") apart from center to center. 68mm (2.68") bolt circle diameter (BCD).Made of yellow zinc plated steel. R48-8 mounting pattern. (search for other parts with R48-8 mounting pattern) Compatibility: Used on some mini bike, dirt bike, pit bike, ATV, quad, trike, and go-kart makes and models. ...

38 Tooth Sprocket for 8mm Chain 100mm (4") OD, 54mm (2-1/8") ID. 4mm thick. 4 bolt mounting pattern. Adjacent mounting bolt holes are spaced 47mm (1-3/8") apart from center to center. F4 mounting pattern (works with 4-hole and 16-tooth freewheels). Made from steel with a zinc-plated finish.

38 Tooth Sprocket for T8F (8mm) Chain 100mm (4") OD, 29.1mm (1.15") ID, 4mm thick. 3 bolt mounting pattern.6.2mm ID bolt holes.Mounting bolt holes are spaced 33.77mm (1.33") apart from center to center.39mm bolt circle diameter.Made from steel with a zinc plated finish.R34 mounting pattern.