SH

Thumb Throttle Standard thumb throttle. Designed to be installed on the right or left hand side of handlebars. Fits 7/8" (22mm) handlebars. Wire colors: black, red, and blue. 62" long throttle cable with 2.8mm male terminals for white wire connectors. The most common connector for this throttle is CNX-52. Wiring Directions ...

36 Volt 1000 Watt Planetary Gear Motor with Cooling Fan 36V 1000W electric bicycle, tricycle, and go-kart motor with built-in planetary gear reduction transmission and cooling fan. Motor speed 3000 RPM. Gear ratio: 6:1 Output shaft speed 500 RPM. Shaft diameter where sprocket seats into is 12mm x 17mm with a dual D-bore. Includes 11 tooth sprocket for #41 and #420 chain (both of these chain sizes work with this motor's sprocket). Powerful four brush permanent magnet design with 100% ball...

Full Length Twist Throttle Left Hand and Right Hand Set Standard full length left hand and right hand throttle set. The left hand throttle that goes from zero throttle to full throttle by twisting it in the clockwise direction. The right hand throttle goes from zero throttle to full throttle by twisting it in the counterclockwise direction.4-1/2" grip lengths. Fits 7/8" (22mm) handlebars. Wire colors: black, red, and white. 62" long throttle cable with male terminals for white wire connectors....

Half Length Twist Throttle with Key Switch Standard half length throttle with key switch. Fits 7/8" (22mm) handlebars. Throttle wire colors: red, black, greenKey Switch wire colors: yellow, white 62" long throttle cable with male terminals for white wire connectors. The most common connector used with this throttle is CNX-52. ...

Heavy-Duty Ratcheting Wire Connector Crimping Tool This ratcheting crimp tool will not release the terminal until the crimp is 100% complete to ensure consistent crimps every time. For CNX-95 Series Wire Connectors.

24VDC 900W 34A 2600RPM Motor Currie Electric Scooter Motor with 11 Tooth Sprocket Specifications: 24V (DC24V), 900W, 2600RPM (R/MIN) Model: XYD-13 (Use model plus specifications to determine compatibility.)Made with powerful neodymium magnets. 11 tooth sprocket for #25 chain. Powerful four brush permanent magnet design with 100% ball bearing construction. Shaft rotation spins Counter Clockwise if you are facing the shaft. Shaft rotation reversible by reversing power leads.OEM Currie electric...

48 Volt Electric Scooter or Bicycle Handlebar Mount Headlight Dashboard with Key Switch, Horn, and Battery Power Indicator 48 Volt handlebar mount headlight with Off-On-On+Headlight 3-position key switch, horn, and battery power level indicator. Power indicator is calibrated for 48 Volts lead-acid battery packs. Has a +48V output wire for tail light. Built-in 48 Volts DC horn requires an external horn switch to operate. Fits standard 7/8" (22mm) electric scooter and bike handlebars. ...

Twist Throttle with Power Meter for 24 Volt eZip, IZIP, Schwinn, GT, and Mongoose Electric Scooters and Bikes (5 Terminal Connector) Aftermarket replacement throttle for 24 Volt Currie, eZip, IZIP, Schwinn, Mongoose, and GT electric scooters and bicycles with 5-wire throttles. Includes matching left and right side handlebar grips. Three LED battery level indicator lights; Min, Mid, Max. 62" long throttle cable with connector. To determine the correct throttle for your electric scooter or bike...

49 Inch Brake Cable with 43 Inch Black Cable Housing

78 Inch Brake Cable with 72 Inch Black Cable Housing

10 Tooth, 10mm D-Bore Sprocket for #25 Chain

35 Tooth Rear Sprocket for T8F (8mm) Chain 93mm (3.67") OD, 29.1mm (1.15") ID, 4mm thick. 3 bolt mounting pattern. 6.2mm ID bolt holes. Mounting bolt holes are spaced 33.77mm (1.33") apart from center to center. 39mm bolt circle diameter. Made from steel with a zinc-plated finish. R34 mounting pattern.