All Parts

Search for The Part You Need

38 Tooth Sprocket for #41 and #420 Chain Made from Aircraft Grade Tempered (Hardened) Aluminum Alloy For #41 and #420 Chain 38 Teeth F4 Mounting Pattern 54.1mm ID Bore Four 6.2mm ID Bolt Holes Equally Spaced @ 90 Degrees 65mm Bolt Circle Diameter

38 Tooth Sprocket for #41 and #420 Chain Made from Aircraft-Grade Tempered (Hardened) Aluminum Alloy For #41 and #420 Chain 38 TeethF5 Mounting Pattern 6" OD 2.125" ID 2.638" Bolt Circle Diameter Five 5.25mm ID Bolt Holes

38 Tooth Sprocket for #410 (1/2" x 1/8") Bicycle Chain with F4 Mounting Pattern Made from Aircraft Grade Tempered (Hardened) Aluminum For #410 (1/2" x 1/8") Bicycle Chain38 TeethF4 Mounting Pattern 2.13" (54.1mm) ID Four 0.244" (6.2mm) ID Bolt Holes Equally Spaced at 90 Degrees 2.559" (65mm) Bolt Circle Diameter

38 Tooth Sprocket for #410 Chain with F5 Mounting Pattern Made from Tempered (Hardened) Aircraft Grade Aluminum Alloy F5 Mounting Pattern38 TeethFor #410 (1/2"x1/8") Chain6.34" Outside Diameter54.1mm ID BoreFive 5.2mm ID Bolt Holes @ 72 degrees67mm Bolt Circle Diameter

38 Tooth Sprocket for T8F (8mm) Chain 100mm (4") OD, 29.1mm (1.15") ID, 4mm thick. 3 bolt mounting pattern.6.2mm ID bolt holes.Mounting bolt holes are spaced 33.77mm (1.33") apart from center to center.39mm bolt circle diameter.Made from steel with a zinc plated finish.R34 mounting pattern.

3mm Front Brake Rotor for Razor MX500, MX650, and SX500 Electric Dirt Bike This is the 3mm thick front brake rotor for newer models. Older models use a 2mm thick brake rotor. Compatible with our BRK-500R-3M disc brake caliper. Older versions have 2mm thick brake rotors and newer versions have 3mm thick brake rotors. A 5 cent nickel is approximately 2mm thick and can be used to determine the rotor's thickness as shown below. ...

3mm Rear Brake Rotor for Razor MX500, MX650, and SX500 Electric Dirt Bike This is the 3mm thick front brake rotor for newer models. Older models use a 2mm thick brake rotor. Compatible with our BRK-500R-3M disc brake caliper. Older versions have 2mm thick brake rotors and newer versions have 3mm thick brake rotors. A 5 cent nickel is approximately 2mm thick and can be used to determine the rotor's thickness as shown below. ...

3mm x 20mm Roll Pin for Chain Sprockets 3mm x 20mm roll pin for eZip, IZIP, Currie, Schwinn, Mongoose, and GT chain motor sprockets.Attaches the sprocket onto motor shaft.

4 Amp ATO Blade Fuse (FUS-ATO4)

FUS-GMA4, 4 Amp GMA Glass Fuse 3/16 inch x 3/4 inch

4 Feet of #410 (1/2" x 1/8") Bicycle Chain Four-foot length of #410 (1/2" x 1/8") bicycle chain. Includes master link. Chain size: 1/2"x1/8" (#410)

4 Inch Jackshaft Kit with 10 Tooth and 17 Tooth Sprockets for #41 and #420 Chain Weld-on jackshaft kit with 10-tooth and 17-tooth sprockets for a 70% increase or decrease in gear ratio. 4-1/2" long x 5/8" OD jackshaft with keyway, 10-tooth and 17-tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on steel bearing hangers, and two jackshaft collars with set screws. This is a complete kit that contains everything needed to install a weld-on...

4 Inch Jackshaft Kit with 12 Tooth and 17 Tooth Sprockets for #41 and #420 Chain Weld-on jackshaft kit with 12-tooth and 17-tooth sprockets for a 41.7% increase or decrease in gear ratio. 4-1/2" long x 5/8" OD jackshaft with keyway, 10-tooth and 17-tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on steel bearing hangers, and two jackshaft collars with set screws. This is a complete kit that contains everything needed to install a weld-on...

4 Inch Jackshaft Kit with 15 Tooth and 20 Tooth Sprockets for #410 (1/2" x 1/8") Chain Weld-on jackshaft kit with 15-tooth and 20-tooth sprockets for a 25% increase or decrease in gear ratio. 4-1/2" long x 5/8" OD jackshaft with keyway, 15-tooth and 20-tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on steel bearing hangers, and two jackshaft collars with set screws. This is a complete kit that contains everything needed to install a weld-on...

4 Inch Jackshaft Kit with 15 Tooth and 25 Tooth Sprockets for #410 (1/2" x 1/8") Chain Weld-on jackshaft kit with 15-tooth and 25-tooth sprockets for a 40% increase or decrease in gear ratio. 4-1/2" long x 5/8" OD jackshaft with keyway, 15-tooth and 25-tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on steel bearing hangers, and two jackshaft collars with set screws. This is a complete kit that contains everything needed to install a weld-on...

Jackshaft Kit with 8 Tooth and 17 Tooth Sprockets for #41 and #420 Chain Weld-on jackshaft kit with 8-tooth and 17-tooth sprockets for a 112.5% increase or decrease in gear ratio. 4" long 5/8" OD jackshaft with keyway. 8 tooth and 17-tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on bearing hangers, and two axle collars with set screws. This is a complete kit that contains everything needed to install a weld-on jackshaft. ...

Jackshaft Kit with 8 Tooth and 25 Tooth Sprockets for #41 and #420 Chain Weld-on jackshaft kit with 8 tooth and 25 tooth sprockets for a 212.5% increase or decrease in gear ratio. 4" long 5/8" OD jackshaft with keyway. 8 tooth and 25 tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on bearing hangers, and two axle collars with set screws. This is a complete kit that contains everything needed to install a weld-on jackshaft. ...

4 Pin Battery/Motor Connector Set With Pins (CNX-160)

4 Pin Black Nylon XLR Charger Port with Cover

4 Pin Black Throttle/Speed Controller Wire Connector Set With Pins (CNX-64)

4 Pin Inline Plug

4 Pin Inline Port

4 Pin Throttle/Speed Controller Connector Set With Pins (CNX-53)

4 Pin XLR Charger Plug

4 Pin XLR Charger Port with 2 Wires and 2 Terminal Connector OEM Currie Tech (eZip and IZIP) Battery Charger PortCurrie Part # BA-071-10Positive (Red Wire) Goes To XLR Port # 1Negative (Black Wire) Goes To XLR Port # 2

4 Pin Black Nylon XLR Charger Port with 3 Wires and 3 Terminal Connector 4-pin XLR electric scooter/bike battery charger port with three wires and a 3-terminal connector.4-inch wire length. 

4 Pin Cord Mount XLR Charger Port

4 Terminal 6.3mm Male Connector to XT60 Female Connector Adapter with Fuse Holder and 30A FuseCan be used to add a lithium battery with XT60 connector to a Razor MX500, MX650, and SX500.

4 Terminal 6.3mm Male Connector to XT90 Female Connector Adapter with Fuse Holder and 30A Fuse Can be used to add a lithium battery with XT90 connector to a Razor MX500, MX650, and SX500.