Y

Set of Four Carbon Brushes for Unite MY1020, MY1020Z, MY1120, and MY1120Z Motors These are original OEM Unite electric motor brushes for electric scooter, bike, tricycle, go-kart, and beach cart/wagon motors. Brush Dimensions: Length: 18mm Width: 10mm Height: 8mm Motor Compatibility:MY1020MY1020ZMY1120MY1120Z

Motor Reversing Switch Motor reversing switch for electric ride-ons, ATVs, go karts and other small electric vehicles. Rated for direct use with motors up to 350 Watts. Can be used for larger motors if used in conjunction with a reverse contactor.Three position switch has back, stop, and forward positions. This is the OEM reverse switch found on many children's ride-on electric vehicles. ...

36 Volt Square 2-Wire Incandescent and LED Turn Signal Flasher Relay Turn signal flasher relay for electric scooters, bikes, and pocket bikes with 36 Volt lighting systems. Works with Incandescent and LED bulbs.Silent flasher without beeper.1/4" (6.3mm) wide tab terminals for push-on connectors.Dimensions of flasher are 1-3/8" x 1-3/8" x 1" excluding terminals and mounting tab. ...

48 Volt Square 2-Wire Incandescent and LED Turn Signal Flasher Relay Turn signal flasher relay for electric scooters, mopeds, and bikes with 48 Volt lighting systems. 48 Volts DC.Rated for loads between 0.02 Watts through 42 Watts.Maximum momentary load 150 Watts.Works with both Incandescent and LED bulbs.Built-in beeper sounds when lights are flashing. 1/4" (6.3mm) wide tab terminals for push-on connectors. Dimensions of flasher are 1" x 1" x 1-1/8" excluding tab terminals. ...

AGC Fuse Holder with Screwdriver Cap Fuse holder for 1/4" x 1-1/4" and 6mm x 30mm AGC glass fuses. Fits many Currie, eZip, and IZIP plastic battery packs for electric bicycles. Cap is removable with a screwdriver to install or replace the fuse.

7.5 Volt 1 Amp Li-ion Battery Charger for Children's Ride On Vehicles For Li-ion BatteriesInput 100-240 VAC 50/60HzOutput 7.5V 1A (1000mA)Output Plug is 5.5mm OD x 2.1/2.5mm IDWorks with both 5.5mm x 2.1mm and 5.5mm x 2.5mm charger ports.

200x45 Electric Scooter Tire and Tube Brand: CST or HOTASize: 200x45Inflate to 28 P.S.I. This is a special order parts which takes around 2-3 weeks for arrival at our warehouse and outbound shipping. -->

2 Port or 3 Port House Charger Plug to 3P Inline Plug Battery Charger Adapter Converts 2 vertical port house plug to 3P Inline plug.Converts 3 vertical port house plug to 3P Inline plug.Converts 2 vertical 1 horizontal (2V1H) port house plug to 3P Inline plug.5 inch long cable between plugs.

8 Tooth 10mm Dual D-Bore Sprocket For 1/2" x 1/8" Bicycle Chain 8.5mm x 10mm ID.Fits 10mm OD dual flatted motor shaft with nut and washer on end to secure sprocket in place.For 1/2" x 1/8" (#410) bicycle chain.

Crimp-on or solder-on 3/16" (4.8mm) tab terminal female connector with flexible clear sleeve. Securely locks onto tab terminals with center holes and is removable by pressing the end of the locking clip. Sleeve has 3mm ID hole for the wire to pass through. For 22-16 gauge wire.

Charging Port for Gotrax GXL V2 Electric Scooter Replacement Charger Port for the Gotrax GXL V2 Electric Scooter Includes mounting nut (not shown in photo). Charger port fits into an 8mm (5/16") mounting hole. May fit other Gotrax electric scooters also if the original charger port looks identical to this one.

Brake Pads for Dokma, Maike, TNE, Nanrobot, Plus Other Electric Scooters and Bikes Semi-Metallic Brake Pads Set of Two Brake Pads with Spring Spacer Fits Nanrobot D4, D4+3.0 (with NANROBOT brakes), and D5 Does Not Fit Nanrobot D4+, D4+2.0, D4+3.0, D5+, or D5+2.0 These Do Available in a Sintered Metallic Version. Known Compatibility: (Electric scooter manufacturers sometimes change brake caliper models mid-production so compare the shape of this brake pad with the old brake pad before...