All Parts

Search for The Parts That You Need

36 Volt 750 Watt Speed Controller with 5-Pin Throttle Connector 36V 750W Electric Scooter Speed Controller for 36 Volt eZip, IZIP, Mongoose, and Schwinn electric scooters with 5 pin throttles. Designed for 36 Volt motors up to 750 Watts. Maximum current 30 Amps. Under Voltage protection 31 Volts. Current limiting feature helps prevent controller and motor damage due to over-current conditions. Under voltage protection feature helps prevent over-discharge and extends battery life. Wiring...

36 Volt 750 Watt Speed Controller (SPD-36750A) plus Twist Throttle with Battery Meter (THR-500)This controller and throttle have matching plugs and are plug-and-play with each other.For Currie, Schwinn, Mongoose, GT, eZip, and IZIP electric scooters.If the scooter or bike's old controller has less connectors on it than this new one has then simply leave the extra connectors disconnected and the controller will operate normally.

36 Volt 750 Watt Speed Controller with 6-Pin Throttle Connector for eZip, IZIP, Currie, Schwinn, GT, and Mongoose Electric Scooters and Bikes For 36 Volt eZip, IZIP, Mongoose, and Schwinn electric scooters with 6 pin throttles. Designed for 36 Volt motors up to 750 Watts. Under Voltage protection 31 Volts. Current limiting feature helps prevent controller and motor damage due to over-current conditions. Under voltage protection feature helps prevent over-discharge and extends battery life....

Wire Lengths: Battery pack to controller wire length 18 inches.Charger port to controller wire length 18 inches.Throttle to controller wire length 64 inches. Kit Features: Push button switch on thumb throttle turns the power on and off.Battery pack wiring harness with fuse holder has 5mm ID ring terminals.Charger port has a sliding cover to keep the sand out of it. The wire lengths can be changed on request. ...

36 Volt 750-800 Watt Electric Scooter/Moped/Bike Brushless DC Motor Speed Controller (CW or CCW with Optional Reverse) Designed for 36V brushless DC motors between 750W and 800W. Replaces controllers with fewer connectors because most of the connectors are optional to use. Under Voltage protection 31.5 Volts. Current limiting feature helps prevent controller and motor damage due to over-current conditions. Under voltage protection feature helps prevent over-discharge and extends battery life....

36 Volt 8 Amp Automatic Battery Charger with 3-Port House Plug

36 Volt 80 Amp Bosch Type SPDT Relay36 Volt DC Coil80 Amp ContactsSingle Pole Double Throw (SPDT)5 TerminalsRelay Dimensions: 1" x 1" x 1" Excluding TerminalsTerminal Dimensions: 1/4" (6.3mm) Wide x 3/8" (10mm) Long

36 Volt 80 Amp Bosch Type SPDT Relay with Mounting Tab

36 Volt 80 Amp SPDT Wide-Pin Relay

36 Volt 800 Watt Controller and Throttle with Key Switch and Battery Indicator Kit Suitable for 36 Volt motors between 750 to 1000 Watts.The only connections that need to be made with this kit are the thick yellow and blue wires to the motor, and the thick red and black wires to the battery pack. All other connectors are optional and do not need to be connected to anything for the controller to operate.The throttle has connectors that are wired to work with the controller. The controller and...

36 Volt 800 Watt Electric Scooter Motor 36V 800W 2750 RPM electric scooter motor. Rated Current: 29.2APowerful four brush permanent magnet design with 100% ball bearing construction. Includes 11 tooth sprocket for #25 chain. 8.5mm x 10mm sprocket mounting area. Different size sprockets are available for this motor.24" long power leads. Shaft rotation reversible by reversing power leads.Motor shaft starts at 12mm OD and is stepped down to 10mm OD with two flat spots that are 8.5mm apart where...

36 Volt 800 Watt Electric Scooter/Pocket Bike Motor 36V 800W 3000 RPM 28.5 Amp electric scooter/pocket bike motor. Powerful four brush permanent magnet design with 100% ball bearing construction. Includes 11 tooth sprocket for 8mm chain. 12 gauge power leads. The two thick red and black wires are for motor power. The two thin red and black wires go to a temperature sensor inside of the motor and are optional to use so they do not need to be connected to anything for the motor to operate. If...