Products 3265-3296 of 6059
Show
Availability: In Stock
Y
Item #: JST-H206 -
Bolt-On Bearing Hanger with Bearing for 5/8" OD Jackshafts Cast iron bearing hanger with bearing for 5/8" OD jackshafts and axles.Bearing collar has two setscrews to hold jackshaft or axle in place.Bearing pivots inside bearing holder for self-alignment so precise alignment of jackshaft and bearing hanger is not necessary. Pre-lubricated and has a grease fitting for relubrication. Mounting bolt holes suitable for 7/16" or 10mm bolts. Length: 4.85" (123mm) Width: 1.28" (32.3mm) Height:...
Availability: In Stock
Y
Item #: BRK-230 -
Brake Cable Adjuster with 10mm Threads Commonly used on the brake lever to adjust the brake cable tension. Aluminum brake cable adjusting barrel with adjustment stop nut. 26mm long x 12mm wide overall measurements not including the stop nut. Fits brake cable ends up to 6mm wide. Threaded area is 15mm long. M10 x 1.00 threads (10mm OD x 1mm pitch).
Availability: In Stock
Y
Item #: BRK-228 -
Brake Cable Adjuster with Mounting Boss Nickel plated steel brake cable adjusting barrel with mounting nut. Most commonly used on caliper type brakes. Fits brake cable housing ends up to 6mm wide. Brake cable adjuster has M6 x 1.00 threads (6mm OD x 1mm pitch). Mounting boss fits into 6mm mounting hole.
Availability: In Stock
Y
Item #: BRK-205 -
Brake Cable End CapSold individually.Made from aluminum alloy.12mm long, 4mm OD, 2.1mm ID.For brake cables up to 2mm OD.
Availability: In Stock
Shared
Item #: PLS-CABLE1 -
Brake Cable for Pulse Bolt, Charger, G Plus, GRT-11, Lightning, Lightwave, Reverb, RK9, Sonic, and Sonic XL Electric Scooters
Availability: In Stock
Y
Item #: BRK-203 -
Brake Cable Housing Ferrule Sold individually.Made from nickel-plated brass.10mm long, 5.1mm OD, 5mm ID, 3.1mm cable hole.For 5mm OD brake cable housings with brake cables up to 3mm OD.
Availability: In Stock
Y
Item #: BRK-215 -
Brake Cable Stopper This cable stop is commonly used for go-kart brake, throttle, and clutch. Works with cables up to 3mm. Material: Steel Finish: White zinc-plated Cable hole diameter: 3mm Outside diameter of barrel: 8mm across flats Length of barrel: 15mm Thread type: M5x0.8 Threads accessible from both ends: YesDrive: Phillips, External Hexagon For wrench size: 8mm ...
Availability: In Stock
Y
Item #: BRK-214 -
Brake Cable Stopper This cable stop is commonly used for go-kart brake, throttle, and clutch. Works with cables up to 2mm. Material: Steel Finish: White zinc-plated Cable hole diameter: 2mm Outside diameter of barrel: 8mm across flats Length of barrel: 9mm Thread type: M4x0.8 Threads accessible from both ends: YesDrive: Combination, Phillips and Flathead ...
Availability: In Stock
Y
Item #: BRK-216 -
Brake Cable Stopper This cable stop is commonly used for motorcycle clutch cables and go-kart brake, throttle, and clutch cables. Works with cables up to 2.5mm. Material: Steel Finish: White zinc-plated Cable hole diameter: 2.5mm Outside diameter of barrel: 6.8mm Length of barrel: 9mm Thread type: M5x0.8 Threads accessible from both ends: No For wrench size:8mmDrive: Phillips, External Hexagon ...
Availability: In Stock
A
Item #: BRK-220 -
Brake Cable Stopper Yellow Zinc Plated Material: Steel Finish: White zinc-plated Cable hole diameter: 2mm Outside diameter of barrel: 6mm Length of barrel: 9mm Thread type: M4x0.8 Threads accessible from both ends: Yes For wrench size: 8mmDrive: Flathead
Availability: In Stock
Shared
Item #: CTE-28010 -
Brake Caliper for eZip, IZIP, Schwinn, Mongoose, and GT Electric Scooters Aftermarket brake caliper for eZip, IZIP, Schwinn, Mongoose, and GT electric scooters. Replacement brake pads for this caliper is Item # BRK-480P.Replacement brake rotor is Item # CTE-28010. Compatibility: eZip E-1000GT GT-750IZIP E3 Zuma CFIZIP E3 Zuma LSCIZIP I-500IZIP I-750, 24 VoltIZIP I-1000IZIP Mountain Trailz AL Men'sIZIP Mountain Trailz AL Women'sIZIP Urban CruiserMongoose CX24V450Schwinn S750 24 Volt Direct...